Accessories
12 position cal pot
AEM part number 30-2056, calibration switch with adjustable end stop allowing anywhere between 2 and..
$50.00 Ex Tax: $50.00
4.7 ohm 25 watt resistor
A resistor like this is necessary for limiting current of suction control valves on Denso common rai..
$10.00 Ex Tax: $10.00
Adjustable fuel pressure regulator
Adjustable from 35-70PSI, perfect for most petrol EFI applications as well as for regulating lift pu..
$130.00 Ex Tax: $130.00
AEM X series wideband lambda controller
The AEM X series 30-0310 wide band lambda controller is a good companion for diesel or petrol t..
$230.00 Ex Tax: $230.00
AEM X series wideband lambda gauge
The AEM X series 30-0300 wide band lambda gauge is a good companion for diesel or petrol tuning..
$250.00 Ex Tax: $250.00
EDC injection pump fuel inlet adapter
This is an adapter made by Elbe Engineering that converts the fuel inlet port on the OM605/OM606 EDC..
$60.00 Ex Tax: $60.00
HBD1 H-bridge driver module
This is an H-bridge driver module that enables any ECU to drive a DC motor using a single PWM output..
$99.00 Ex Tax: $99.00
HSD4 4 channel high side driver
This is effectively a 4 channel solid state relay, with inputs triggered by low-side switch outputs ..
$99.00 Ex Tax: $99.00
ITM8 8 channel ignition transistor module
The ITM8 is a power transistor module designed to drive up to 8 passive ignition coils (those withou..
$129.00 Ex Tax: $129.00
Low voltage VR module for LPC4
This is an input amplifier module that enables the LPC4 to reliably trigger off poor quality VR sens..
$15.00 Ex Tax: $15.00
LPCX2 I/O expansion board
This expansion board fits inside LPC4 (all variants) and DSL1 ECUs (Serial number 200 and up) and ad..
$220.00 Ex Tax: $220.00
MAC 3 port boost control valve
This is a MAC Valves Inc. 35A-ACA-DDBA-1BA three port solenoid valve suitable for turbocharger boost..
$60.00 Ex Tax: $60.00
Mercedes injection pump lift pump delete plate
This is a plate made by Elbe Engineering that replaces the mechanical lift pump on the Mercedes Benz..
$12.00 Ex Tax: $12.00
Mini Fit Jr pin extraction tool
Molex part number 11030044, a tool to extract the pins from the Mini Fit Jr connectors used on ..
$35.00 Ex Tax: $35.00
Molex hand crimper
This is a Molex P/N 0638111000 low cost hand crimper. It's suitable for crimping Molex Mini-fit jr t..
$90.00 Ex Tax: $90.00
Nissan Patrol transmission interface
This little box includes 5 high side (positive) outputs and a multiplexer to convert a transmission ..
$179.00 Ex Tax: $179.00
OBDLink LX bluetooth adapter
This is the premium OBD2 to Bluetooth adapter on the market. There are other lower cost options but ..
$125.00 Ex Tax: $125.00
PCS gear position indicator
The PCS gear indicator scans a vehicle's CAN bus and displays current gear data allowing technicians..
$250.00 Ex Tax: $250.00
PCS TCM2800 722.6 controller kit
This is a robust and repeatable transmission controller sold in a kit with wiring harness and specia..
$1,499.00 Ex Tax: $1,499.00
Ratcheting crimper for DID1 ECU pins
This is a ratcheting crimper suitable for crimping the MQS terminals found on the DID1 ECU as well a..
$40.00 Ex Tax: $40.00
Walbro/TI GSL392 inline fuel pump
This is an inline fuel pump, suitable for petrol fuel injection as well as diesel lift pump duties.I..
$170.00 Ex Tax: $170.00